/https://fbi.cults3d.com/uploaders/21248153/illustration-file/0c28fa77-8860-44fe-a22e-90464130230d/IMG_1170.jpg?w=516&resize=516,516&ssl=1 "🍽️ Lenovo P11 Gen 2")
Wall Mounted Pill Holder designed to work for the Lenovo P11 Gen 2 – 11.5 inch pill.
For non North American installations, use Set up Possibility 2 or 3.
This was parametrically designed in FreeCad. In case you are focused on a design for another pill mannequin, I could also be focused on modifying the design for different pill sizes.
This design is for Panorama Orientation and makes use of much less filament and I feel is probably the most acceptable orientation.
There are 4 STL recordsdata included within the buy:
- Lenovo P11 Gen 2 – V1 – Left – it’s the removeable aspect with allowances for the Quantity or Energy buttons (I might advocate this one as it’s simple sufficient to slip open the mount to press the facility button)
- Lenovo P11 Gen 2 – V1 – Proper with Finger Slot – It’s the completely mounted aspect that homes your USB cable you provide. (Essential to make use of the one I advised or you’ll probably want to interrupt out the dremel)
- Lenovo P11 Gen 2 – V1 – Proper No Finger Slot – It’s the identical because the above with no finger slot.
- Lenovo P11 Gen 2 – V1 – USB Connector Filler – It’s a USB Connecter filler to carry the USB connector safe (You need to use scorching glue to safe it, as soon as USB cable is put in and aligned)
Have in mind, the proper wall mounts are particularly designed for the USB-C cables famous. If you happen to use one other kind, it could require dremel work and scorching glue to maintain it within the correct place.
INSTALLATION OPTION 1 (Most troublesome however most elegent answer. Requires excessive voltage wiring work.):
The design is made to work with a completely mounted “ARLINGTON INDUSTRIES DVFR1WGC 1-Gang Arlington Recessed Indoor IN BOX” and a Leviton 110 volt (or related) duplex outlet with USB kind C energy connectors. See Different Set up Possibility 2 directions for a less expensive set up possibility.
You must set up a Duplex 110v plug outlet with at the very least one USB Kind-C Port. These are generally out there at a retailer like House Depot or Lowes. I’ve supplied a photograph of 1 possibility.
Set up Possibility 1 directions:
1) Set up the Arlington Recessed energy field within the acceptable location per directions that got here with it. Don’t use the slide on cowl plate provided, because the Proper 3D print replaces it. Make sure the field is plumb and never crooked as it can have an effect on the extent of the pill mount. Use shims if vital.
2) Run the facility wire into the field after which set up the duplex outlet into the field, and inside outlet cowl.
3) Set up the USB-C cable into the Proper 3D printed bracket. Use scorching glue to safe it with the USB cable spacer printed out. I like to recommend orienting the cable with the pill slid in to make sure the right orientation previous to gluing it. This can guarantee much less stress on the pill for bother free use.
5) Orient the USB-C cable within the recessed slot on the underside of the Proper 3D print. Use a dab of scorching glue for those who wish to maintain it in place for those who like.
6) Set up 3M VHB double sided tape within the acceptable recesses on the underside aspect of the Proper 3D print.
7) Plug within the USB cable to the plug outlet USB receptacle.
8) Set up the Proper 3D print on the Recessed Arlington field. Make sure the USB Cable is fed by way of the slot and never pinched. Safe the Proper 3D print with the provided screws however don’t overtighten them as you’ll crack the 3D print.
9) Press the 1/2 huge, 3M VHB double sided tape to the wall. That is optionally available however really helpful. It’s out there on Amazon or brick and mortar shops.
10) Slide within the pill into the proper wall mount till the USB-C cable is plugged in to the pill.
11) Congratulate your self, as you are actually accomplished.
SAFETY NOTICE: Have in mind the set up above requires you to work with 110V energy. In case you are not comfy doing this, and alternate methodology of set up is to make use of the ten Foot USB cable under and feed it by way of the wall to the baseboard space, then out the wall to a plug outlet. Set up is far simpler, however not as elegant.
INSTALLATION OPTION 2 (USB cable extra seen that Possibility 1, however much less seen that Possibility 3):
Alternatively, this may be put in with no recessed plug outlet.
Use the longer USB-C 2 meter or 3 meter cable to be fed from the Proper Mount to the wall to a plug adaptor:
https://www.amazon.ca/gp/product/B085G36K9V/ref=ox_sc_act_title_1?smid=AKXVBT49GGF3B&th=1
https://www.amazon.ca/gp/product/B07PLYZ7J3/ref=ox_sc_act_title_1?th=1
Set up Possibility 2 directions:
1) Drill two holes (appropriately sized to suit the connector by way of). One behind the Proper mount aligned with the USB cable path, and one drilled into the wall close to the baseboard, near a plug outlet in the identical stud cavity.
2) Fish the longer USB-C cable between the 2 holes.
3) Align the Proper mount on the wall and mark the holes to be drilled. Set up plastic screw anchors flush to the wall.
4) Set up the USB cable into the Proper 3D printed bracket. Use scorching glue to safe it with the USB cable filler (printed). I like to recommend orienting the cable with the pill slid in to make sure the right orientation previous to gluing it. This can guarantee much less stress on the pill for bother free use.
5) Orient the USB cable within the recessed slot on the underside of the Proper 3D print. You can use a dab of scorching glue for those who like. Orient the cable slot to align with the higher gap within the wall.
6) Set up 3M VHB double sided tape within the acceptable recesses on the underside aspect of the Proper 3D print.
7) Set up the Proper 3D print on the wall. Make sure the USB Cable is fed by way of the slot and never pinched. Safe the Proper mount with acceptable chamfered screws. WARNING – be certain that the screw head doesn’t protrude and intervene with the again of the pill (in any other case it could scratch your pill) and don’t overtighten them as you might crack the 3D print.
8) Press the 1/2 huge, 3M VHB double sided tape to the wall. That is optionally available however really helpful. It’s out there on Amazon or brick and mortar shops.
9) Slide within the pill into the proper wall mount till the USB cable is plugged in to the pill.
11) Slide the Left mount print across the pill and into the slots of the Proper 3D print. The pill might be adjusted in setting to not energy off. If it is advisable to press the facility button simply slide the Left mount open to press it.
12) Plug the opposite finish of the USB cable into an influence block.
13) Congratulate your self, as you are actually accomplished.
INSTALLATION OPTION 3 (USB cable extra seen that Possibility 2 however requires no holes to be drilled within the wall for the USB cable):
Use the longer USB-C 2 meter or 3 meter cable to be fed from the Proper Mount to the wall to a plug adaptor:
https://www.amazon.ca/gp/product/B085G36K9V/ref=ox_sc_act_title_1?smid=AKXVBT49GGF3B&th=1
https://www.amazon.ca/gp/product/B07PLYZ7J3/ref=ox_sc_act_title_1?th=1
Set up Possibility 3 directions:
1) Usings a dremel or aspect cutters, take away the knock out on the Proper aspect mount for the USB cable to exit on the underside of the mount. See CAD drawing.
2) Align the Proper mount on the wall and mark the mounting screw holes to be drilled. Set up plastic screw anchors flush to the wall. Alternatively mount screws right into a stud.
2) Set up the USB-C cable into the Proper 3D printed bracket. Use scorching glue to safe it with the USB cable filler (printed). I like to recommend orienting the cable with the pill slid in to make sure the right orientation previous to gluing it. This can guarantee much less stress on the pill for bother free use.
3) Orient the USB-C cable within the recessed slot on the underside of the Proper 3D print. You can use a dab of scorching glue for those who like. I did not must.
4) Set up 3M VHB double sided tape within the acceptable recesses on the underside aspect of the Proper 3D print.
5) Set up the Proper 3D print on the wall. Make sure the USB Cable is fed by way of the slot and never pinched. Safe the Proper mount with acceptable chamfered screws. WARNING – be certain that the screw head doesn’t protrude and intervene with the again of the pill (in any other case it could scratch your pill) and don’t overtighten them as you might crack the 3D print.
6) Press the 1/2 huge, 3M VHB double sided tape to the wall. That is optionally available however really helpful. It’s out there on Amazon or brick and mortar shops.
7) Slide within the pill into the proper wall mount till the USB cable is plugged in to the pill.
8) Slide the Left mount print across the pill and into the slots of the Proper 3D print. The pill might be adjusted in setting to not energy off. If it is advisable to press the facility button simply slide the Left mount open to press it.
9) Plug the opposite finish of the USB cable into an influence block and conceal the wiring as you want.
10) Congratulate your self, as you are actually accomplished.
/https://fbi.cults3d.com/uploaders/21248153/illustration-file/0c28fa77-8860-44fe-a22e-90464130230d/IMG_1170.jpg?w=1200&resize=1200,0&ssl=1&description=%F0%9F%8D%BD%EF%B8%8F+Lenovo+P11+Gen+2){kind=link}